Prop Terminology

Diameter is two times the distance from the center of the hub to the tip of the blade. It also can be looked at as the distance across the circle that the propeller would make when rotating.  It is the first number listed  when describing a propeller.

 Pitch is defined as the theoretical forward movement of a propeller during one revolution –– assuming there is no “slippage” between  the propeller blade and the water. For most boats, there is slippage and therefore the distance advanced is less than the design pitch. The amount of slippage varies from boat to boat. Pitch is the second number listed in the propeller description. 

Cupping of today’s propellers incorporate a cup at the trailing edge of the propeller blade. This curved lip on the  propeller allows it to get a better bite on the water. This results in reduced ventilation, slipping, and allows for a better hole shot in many cases. A cupped propeller also works very well where the motor can be trimmed so that the propeller is near the surface of the water. The cup will typically result in less higher top end speed on some of these applications.

Rake is the degree that the blades slant forward or backwards in relation to the hub. Rake can affect the flow of water through the propeller, and as implications with  respect to boat performance.  Aft Rake helps to trim the bow of the boat upwards, which often results in less wetted surface area and therefore higher top end speed. Aft rake propellers also typically “bite” better on ventilating type applications.   Forward, or negative rake, helps hold the bow of the boat down. This is more common in workboat type applications.

Ventilation is a situation where surface air or exhaust gasses are drawn into the propeller blades. When this situation occurs, boat speed is lost and engine RPM climbs rapidly. This can result from excessively tight cornering, a motor that is mounted very high on the transom, or by over-trimming the engine.

Cavitation, (which is often confused with ventilation), is a phenomena of water vaporizing or “boiling” due to the extreme reduction of pressure on the back of the propeller blade. Many propellers partially cavitate during normal operation, but excessive cavitation can result in physical damage to the propeller’s blade surface due to the collapse of microscopic bubbles on the blade.

There may be numerous causes of cavitation such as incorrect matching of propeller style to application, incorrect pitch, physical damage to the blade edges, etc...

Be advised disturbances in the water flow forward of the propeller can result in blade damage which appears to be blade cavitation, but is actually due to non-favorable water flow into the propeller.

 PROPELLER CHARACTERISTICS:  Finding the right match between the propeller, engine type and boat size will optimize the following performance factors — increased top end, faster planing speed, improved low end punch and load carrying capability.   If you want to modify your boat’s performance, consider the following before making your selection.

3 Blades or 4 Blades:  A recommendation of  3-blade propellers for recreational boats with 3, 4, and 6 cylinder outboards and I/O engines. These propellers provide good “hole shot” and top-speed performance.   And a recommendation of 4-blade propellers for bass boats and boats with high performance hulls running high horsepower outboard engines. Compared to 3 blades, they provide better “hole shot” performance with less steering torque and less vibration at high speeds.

The advantage of a left-hand prop is two propellers spinning the same direction on twin-engine boats will create steering torque. In other words, two right-hand propellers pull the stern hard to the right and the bow to the left.   Two opposite-direction propellers on twin engines eliminate this steering torque because the left-hand propeller balances out the right-hand propeller. This results in better straight-line tracking and helm control at high speed.

Propeller diameter, pitch, and slip is the difference between actual and theoretical travel of the propeller blades through water.  A properly matched propeller will actually move forward  about 80 to 90 percent of the theoretical pitch.

Thru-hub exhaust propellers consist of a round barrel to which the blades are attached. The exhaust passes through the barrel and out the back, without making contact with the propeller blades. This provides a good clean water flow to the blades, usually resulting in good acceleration and hole shot.

Over/Thru-hub exhaust propellers are a combination of thru-hub and over-hub exhaust propellers. This allows some exhaust to escape at lower RPM, providing a controlled amount of exhaust flooding. These types of propellers will allow the propeller to be slightly easier to turn during initial acceleration, allowing for a better hole shot on some engine/boat combinations.

Non thru-hub exhaust propellers are used for inboards using shaft driven propellers, stern drives using through hull exhaust, and on some outboards that don’t route the exhaust through the lower unit torpedo.

Aluminum vs. Stainless Steel: Aluminum propellers are relatively inexpensive, easy to repair, and under normal conditions can last for many years.  Stainless steel is more expensive, but much stronger and durable than aluminum. If you are looking for better performance than can be provided by your aluminum propeller, such as ultimate top speed or better acceleration, a stainless steel propeller may be required.

Determining RPM:  Determine the Wide Open Throttle (WOT) RPM for safety and efficient performance, it is critical that your engine operates within the RPM range recommended by the manufacturer. Matching the right prop for the load is the most significant factor of RPM adjustment.